Description: |
Table Type Boring and Milling Machine KRAFT HBM-130 | HBM-130L | HBM-130XL
machine nouvelle
:HBM-130 | HBM-130L | HBM-130XL spindle diameter:130|130|130
mm x-travel:1600|2000|2000 mm y-travel:1400|1800|1800
mm z-travel:2000 mm U-axis:250 mm W-axis (spindle
longitudinal):900 mm max. torque on the spindle:3200 Nm B-axis
(table):360x1 ° rapid speed:X/Y/Z/W: 2500 mm/min table
load:8|10|10 t table-size:1600 x 1400|1800 x 1600|2200 x 2000
mm T-slots:9/11/12 Stk. T-slot - width:28 mm transmission
ratio:4 Stk. spindle speed:4-800 1/min spindle taper:50
ISO faceplate:Drehmoment: 4900 Nm faceplate:2.5-125
1/min faceplate:Umdrehung stufenlos einstellbar
faceplate:Ø:750 mm weight of the machine ca.:22,5|24,5|25,5
t main drive:22 kW Machine size
(LxWxH):6995/3647/342|7030/4665/3800|7030/4665/3800 mm PLC
control:Siemens S7 servo motors:von Siemens/Fanuc/Fagor
Technical Offer of HBM-130 ? Powerful servo spindle
motor and four spindle speed rang, stepless in each range. much lower
maintenance and 80% failure rate reduced ? High rigidity
spindle could insure the strong machining ? Worktable 4x90°
position by the collimator ? X,Y, Z, B axes DRO are
available ? Spindle could choose ISO50, with automatic
clamping
1. Introduce The horizontal boring and
milling machine series HBM-130 of our company is suitable for such
operation as drilling, counter-boring, boring, reaming, spot-facing,
tapping and milling etc. Also the horizontal boring and milling
machine type is equipped with fixed facing head on which radial facing
slide can be radically feed consequently to enable the machine to
undertake boring of large-diameter hole, external cutting ,end face
turning and recessing, etc. The machine is composed of bed, front
column, headstock, cross and longitudinal saddle, worktable, back
column and balance weight pulley etc. The vertical movement of
headstock goes along the column's guideway, the worktable can move
transversely and longitudinally on the bed, and the worktable can be
rotated.
The characteristics of HBM-130 2.1 The big
servo spindle 22KW motor supply continuously speed change and high
torque output of headstock. Four speed range can
be changed by the selector on the control panel. The infinit
speed change in each range can be effected continuously and smoothly.
It?s very simple and convenient for machine operation.
Compare with old headstock structure, 24 steps speed changing by
hydraulic, the failure rate will be reduced 80%. 2.2 The
vertical coordinate ( headstock lifting direction ) and cross
coordinate ( worktable transverse movement ) and longitudinal
coordinate ( worktable longitudinal movement--option ) are provided
with new type digital read out unit with memory function, which makes
the machine with complete function and high accuracy. 2.3 Main
parts of the machine such as bed, front column and guideways of
longitudinal saddle are all hardened and ground, which bring high
stiffness of the guideways and extend the using life of the
machine. 2.4 The horizontal guideway surface of the machine is
provided with all pull-board type dust-proof. 2.5
Electric-hydraulic interlocking device will be fixed between the
moving units and when a moving unit is working, the other moving units
will be clamped automatically (except spindle, radial facing
slide). 2.6 In the rapid traverse gearbox, safety clutches are
installed to prevent the machine from overload.
3.
Transmission systems of the machine 3.1 Headstock transmission
The rotation movement of boring spindle are driven by CTB servo
spindle motor directly. Insteady of old design, 24 steps spindle
speed, the spindle servo motor supply two range speed. Low spindle
speed with big torque output and G41232403 high spindle speed with
stable and continuously cutting forece. 3.2 Feed motion The
feed motion of all moving units of this machine is feeding per spindle
revolution (e.g. traverse rate of spindle, headstock, table per
spindle revolution).The power of various moving units comes from shaft
driven by main driven motor. It can be transmitted through gears of
speed-change device to shaft (the feed safety mechanism). After that
the motion will be transmitted further through the forward and reverse
mechanism, to the feed shaft, then to the lead-screw or gear racks of
various moving units, enable the headstock, cross & longitudinal
saddles to obtain each 18 steps feed rates at low and high gear
respectively. The feed motion of the radial slide on the facing
head comes from headstock, enable it to obtain various feed
rates. 3.3 Rapid transmission system The rapid moving of the
headstock,cross & longitudinal saddles of the machine and the rapid
rotation of the rotary worktable are driven by AC motor mounted at the
right side of the bed. Power from the motor is transmitted from shafts
coupling and friction clutch to each moving units respectively, enable
the spindle, headstock and cross & longitudinal saddles to obtain the
rapid moving speed 2500mm/min, the rapid rotation of the worktable is
1r/min.
4. Hydraulic system of the machine The
hydraulic system is located inside of longitudinal saddle of the
machine, which is used for the transverse of headstock, longitudinal &
cross movement, rotation of worktable, feed speed change and internal
lubrication of headstock
seller offer No. resale 1124-94305
|